How to Install Fail2Ban to Protect SSH on CentOS/RHEL 8

Fail2ban is a free, open-source and widely used intrusion prevention tool that scans log files for IP addresses that show malicious signs such as too many password failures, and much more, and it bans them (updates firewall rules to reject the IP addresses). By default, it ships with filters for various services including sshd.

Read Also: Initial Server Setup with CentOS/RHEL 8

In this article, we will explain how to install and configure fail2ban to protect SSH and improve SSH server security against brute force attacks on CentOS/RHEL 8.

Installing Fail2ban on CentOS/RHEL 8

The fail2ban package is not in the official repositories but it is available in the EPEL repository. After logging into your system, access a command-line interface, then enable the EPEL repository on your system as shown.

# dnf install epel-release
# dnf install
Install EPEL Repo on CentOS and RHEL 8
Install EPEL Repo on CentOS and RHEL 8

Afterward, install the Fail2ban package by running the following command.

# dnf install fail2ban
Install Fail2ban in CentOS and RHEL 8
Install Fail2ban in CentOS and RHEL 8

Configuring Fail2ban to Protect SSH

The fail2ban configuration files are located in the /etc/fail2ban/ directory and filters are stored in the /etc/fail2ban/filter.d/ directory (the filter file for sshd is /etc/fail2ban/filter.d/sshd.conf).

The global configuration file for the fail2ban server is /etc/fail2ban/jail.conf, however, it is not recommended to modify this file directly, as it will probably be overwritten or improved in case of a package upgrade in the future.

As an alternative, it is recommended to create and add your configurations in a jail.local file or separate .conf files under the /etc/fail2ban/jail.d/ directory. Note that configuration parameters set in jail.local will override whatever is defined in jail.conf.

For this article, we will create a separate file called jail.local in the /etc/fail2ban/ directory as shown.

# vi /etc/fail2ban/jail.local

Once the file is open, copy and paste the following configuration in it. The [DEFAULT] the section contains global options and [sshd] contains parameters for the sshd jail.

ignoreip =
bantime  = 21600
findtime  = 300
maxretry = 3
banaction = iptables-multiport
backend = systemd

enabled = true
Fail2ban Configuration
Fail2ban Configuration

Let’s briefly explain the options in the above configuration:

  • ignoreip: specifies the list of IP addresses or hostnames not to ban.
  • bantime: specified the number of seconds that a host is banned for (i.e effective ban duration).
  • maxretry: specifies the number of failures before a host gets banned.
  • findtime: fail2ban will ban a host if it has generated “maxretry” during the last “findtime” seconds.
  • banaction: banning action.
  • backend: specifies the backend used to get log file modification.

The above configuration, therefore, means if an IP has failed 3 times in the last 5 minutes, ban it for 6 hours, and ignore the IP address

Next, start and enable the fail2ban service for now and check if it is up and running using the following systemctl command.

# systemctl start fail2ban
# systemctl enable fail2ban
# systemctl status fail2ban
Start Fail2ban Service
Start Fail2ban Service

Monitoring Failed and Banned IP Address Using fail2ban-client

After configuring fail2ban to secure sshd, you can monitor failed and banned IP addresses using the fail2ban-client. To view the current status of the fail2ban server, run the following command.

# fail2ban-client status
Check Fail2ban Jail Status
Check Fail2ban Jail Status

To monitor the sshd jail, run.

# fail2ban-client status sshd
Monitor SSH Failed Logins with Fail2ban
Monitor SSH Failed Logins with Fail2ban

To unban an IP address in fail2ban (in all jails and database), run the following command.

# fail2ban-client unban

For more information on fail2ban, read the following man pages.

# man jail.conf
# man fail2ban-client

That sums up this guide! If you have any questions or thoughts you want to share about this topic, do not hesitate to reach us via the feedback form below.

If you liked this article, then do subscribe to email alerts for Linux tutorials. If you have any questions or doubts? do ask for help in the comments section.

If You Appreciate What We Do Here On TecMint, You Should Consider:

TecMint is the fastest growing and most trusted community site for any kind of Linux Articles, Guides and Books on the web. Millions of people visit TecMint! to search or browse the thousands of published articles available FREELY to all.

If you like what you are reading, please consider buying us a coffee ( or 2 ) as a token of appreciation.

Support Us

We are thankful for your never ending support.

4 thoughts on “How to Install Fail2Ban to Protect SSH on CentOS/RHEL 8”

  1. Fail2ban is a way too old method to use for security. You should always use ssh-keys and (google) authenticator if you use ssh from the internet (less than 5 minutes to setup). And just change the default port to something else so your logs won’t get full of script-kiddies try-outs.

    • fail2ban is one of several tools for securing a system, and it doesn’t just apply to SSH.

      Yes, use 2FA; but still, use fail2ban as it helps limit the number of attempts in breaking in. However old it may be, it’s still a key tool in security.

      • Agree 100%.

        Two entirely different issues here. 2FA is always the best practice, but SSH is just one service.

        2FA won’t protect the other public-facing services you may be running from a brute-force attack. Fail2ban does that quite well. The fact that it’s been around a long time isn’t relevant. It works.


Got something to say? Join the discussion.

Have a question or suggestion? Please leave a comment to start the discussion. Please keep in mind that all comments are moderated and your email address will NOT be published.

This site uses Akismet to reduce spam. Learn how your comment data is processed.