How to Add a New Disk to an Existing Linux Server

As system administrators, we would have got requirements wherein we need to configure raw hard disks to the existing servers as part of upgrading server capacity or sometimes disk replacement in case of disk failure.

In this article, I will take you through the steps by which we can add the new raw hard disk to an existing Linux server such as RHEL/CentOS or Debian/Ubuntu.

Suggested Read: How to Add a New Disk Larger Than 2TB to An Existing Linux

Important: Please note that the purpose of this article is to show only how to create a new partition and doesn’t include partition extension or any other switches.

I am using fdisk utility to do this configuration.

I have added a hard disk of 20GB capacity to be mounted as a /data partition.

fdisk is a command line utility to view and manage hard disks and partitions on Linux systems.

# fdisk -l

This will list the current partitions and configurations.

Find Linux Partition Details
Find Linux Partition Details

After attaching the hard disk of 20GB capacity, the fdisk -l will give the below output.

# fdisk -l
Find New Partition Details
Find New Partition Details

New disk added is shown as /dev/xvdc. If we are adding physical disk it will show as /dev/sda based of the disk type. Here I used a virtual disk.

To partition a particular hard disk, for example /dev/xvdc.

# fdisk /dev/xvdc

Commonly used fdisk commands.

  • n – Create partition
  • p – print partition table
  • d – delete a partition
  • q – exit without saving the changes
  • w – write the changes and exit.

Here since we are creating a partition use n option.

Create New Partition in Linux
Create New Partition in Linux

Create either primary/extended partitions. By default we can have upto 4 primary partitions.

Create Primary Partition
Create Primary Partition

Give the partition number as desired. Recommended to go for the default value 1.

Assign a Partition Number
Assign a Partition Number

Give the value of the first sector. If it is a new disk, always select default value. If you are creating a second partition on the same disk, we need to add 1 to the last sector of the previous partition.

Assign Sector to Partition
Assign Sector to Partition

Give the value of the last sector or the partition size. Always recommended to give the size of the partition. Always prefix + to avoid value out of range error.

Assign Partition Size
Assign Partition Size

Save the changes and exit.

Save Partition Changes
Save Partition Changes

Now format the disk with mkfs command.

# mkfs.ext4 /dev/xvdc1
Format New Partition
Format New Partition

Once formatting has been completed, now mount the partition as shown below.

# mount /dev/xvdc1 /data

Make an entry in /etc/fstab file for permanent mount at boot time.

/dev/xvdc1	/data	ext4	defaults     0   0
Conclusion

Now you know how to partition a raw disk using fdisk command and mount the same.

We need to be extra cautious while working with the partitions especially when you are editing the configured disks. Please share your feedback and suggestions.

If you liked this article, then do subscribe to email alerts for Linux tutorials. If you have any questions or doubts? do ask for help in the comments section.

If You Appreciate What We Do Here On TecMint, You Should Consider:

TecMint is the fastest growing and most trusted community site for any kind of Linux Articles, Guides and Books on the web. Millions of people visit TecMint! to search or browse the thousands of published articles available FREELY to all.

If you like what you are reading, please consider buying us a coffee ( or 2 ) as a token of appreciation.

Support Us

We are thankful for your never ending support.

30 thoughts on “How to Add a New Disk to an Existing Linux Server”

  1. If I create a /home folder on the second drive, will it merge with the /home folder on the first drive? Can not be afraid of data loss of the first disk?

    Reply
  2. Hi there,

    I have a problem using Ubuntu. I have installed two hard drives one 128GB SSD and the other is 500 HD. On by default, I set 128 as a boot like using window and ubuntu at a time.

    I have a problem there is when I open window in dual boot mode all partition work normal and good but when I open ubuntu my 500 Gb disk cannot show on ubuntu platform what I happen.

    my all data exist on 500gb hard and I cannot see in ubuntu please guide some tricks

    Reply
  3. Thanks — I was able to follow this guide and get my drive installed with no headaches at all!

    It might be useful to update with instructions to change the owner of the newly assigned drive. In Ubuntu 16.04, my freshly installed drive belonged to the user `root` and the group `root`. I just had to run `sudo chown : /dev/sda1` (in Ubuntu it seems both name and group are your login name) to get write access to the drive.

    Reply
  4. In your /etc/fstab consider using the UUID instead of the automatically assigned /dev/***.
    UUID can be found using blkid.

    e.g. fstab

    UUID=******-*******-******-******	/data	ext4	defaults     0   0
    
    Reply

Leave a Reply to Arun Cancel reply

Have a question or suggestion? Please leave a comment to start the discussion. Please keep in mind that all comments are moderated and your email address will NOT be published.

This site uses Akismet to reduce spam. Learn how your comment data is processed.