How to Synchronize Time with Chrony NTP in Linux

The Network Time Protocol (NTP) is a protocol used to synchronize computer system clocks automatically over a network. The machine can have the system clock use Coordinated Universal Time (UTC) rather than local time.

Maintaining accurate time on Linux systems, especially servers is an important task for many reasons. For example, in a networked environment, accurate timekeeping is required for accurate timestamps in packets and system logs for root-cause analysis, determining when problems occurred, and finding correlations.

Chrony is now the default NTP implementation package on the latest versions of RHEL-based distributions such as CentOS Stream, Fedora, Rocky Linux & AlmaLinux, and Debian-based distributions such as Ubuntu & Linux Mint, among others, and comes pre-installed by default.

The Chrony package consists of chronyd, a daemon that runs in userspace, and chronyc a command-line program for monitoring and controlling chronyd.

Chrony is a versatile NTP implementation and performs well in a wide range of conditions (check out the comparison of the chrony suite to other NTP implementations). It can be used to synchronize the system clock with NTP servers (act as a client), with a reference clock (e.g a GPS receiver), or with a manual time input. It can also be employed as an NTPv4 (RFC 5905) server or peer to provide a time service to other computers in the network.

In this article, you will learn how to synchronize server time with NTP in Linux using chrony.

Installing Chrony in Linux Server

In most Linux systems, the chrony command is not installed by default. To install it, execute the below command.

$ sudo yum install chrony         [On RHEL/CentOS/Fedora and Rocky Linux/AlmaLinux]
$ sudo apt install chrony         [On Debian, Ubuntu and Mint]
Install Chrony in Linux
Install Chrony on Linux

The default location for the chrony daemon is /usr/sbin/chronyd and the command line program will be installed to /usr/bin/chronyc.

Once the installation is complete, start the chrony service and enable it to automatically start at system boot, then check if it is up and running.

# systemctl enable --now chronyd
# systemctl status chronyd
Check Chrony Status
Check Chrony Status

To cross-check if chrony is now up and running fine and to see the number of servers and peers that are connected to it, run the following chronyc command.

# chronyc activity
Check Chrony Activity
Check Chrony Activity

Checking Chrony Synchronization in Linux

To display information (list of servers available, status, and offsets from the local clock and the source) about the current time sources that chronyd is accessing, run the following command with the -v flag shows the description for each column.

# chronyc sources
OR
# chronyc sources -v
Check Chronyd Time Sources
Check Chronyd Time Sources

Concerning the previous command, to display other useful information for each of the sources currently being examined by chronyd (such as the drift rate and offset estimation process), use the sourcestats command.

# chronyc sourcestats
OR
# chronyc sourcestats -v
Check Chronyd Source Stats
Check Chronyd Source Stats

To check chrony tracking, run the following command.

# chronyc tracking

In the output of this command, the reference ID specifies the name (or IP address) if available, of the server to which the computer is currently synchronized, out of all the available servers.

Display Chrony Tracking
Display Chrony Tracking

Configuring Chrony Time Sources in Linux

The main chrony configuration file is located at /etc/chrony.conf (CentOS/RHEL/Fedora) or /etc/chrony/chrony.conf (Ubuntu/Debian).

When installing a Linux OS in the cloud, your system should have some default servers or a pool of servers added during the installation process. To add or change the default servers, open the configuration file for editing:

# vi /etc/chrony.conf
OR
# vi /etc/chrony/chrony.conf

You can either add several servers using the server directive as shown.

server 0.europe.pool.ntp.org iburst
server 1.europe.pool.ntp.org iburst
server 2.europe.pool.ntp.org ibusrt
server 3.europe.pool.ntp.org ibusrt
Add NTP Servers
Add NTP Servers

or in most cases, it’s best to use ntppool.org to find an NTP server. This allows the system to try to find the closest available servers for you. To add a pool, use the pool directive:

pool 0.pool.ntp.org burst
Add a Pool of NTP Servers
Add a Pool of NTP Servers

There are many other options you can configure in the file. After making changes, restart the chrony service.

$ sudo systemctl restart chrony		
OR
# systemctl restart chronyd

To show information about the current time sources that chronyd is querying, run the following command once more.

# chronyc sources
View Chronyd Time Sources
View Chronyd Time Sources

To check the chrony tracking status, run the following command.

# chronyc tracking
Check Chrony Synchronizing Status
Check Chrony Synchronizing Status

To display the current time on your system, check whether the system clock is synchronized and whether NTP is indeed active, run the timedatectl command:

# timedatectl
Check Current Server Time
Check the Current Server Time

That brings us to the end of this guide. If you have any questions, reach us via the comment section below. For more information, check out: using the chrony suite to configure NTP from the RHEL documentation or using chrony to configure NTP from the Ubuntu official blog.

Matei Cezar
I'am a computer addicted guy, a fan of open source and linux based system software, have about 4 years experience with Linux distributions desktop, servers and bash scripting.

Each tutorial at TecMint is created by a team of experienced Linux system administrators so that it meets our high-quality standards.

Join the TecMint Weekly Newsletter (More Than 156,129 Linux Enthusiasts Have Subscribed)
Was this article helpful? Please add a comment or buy me a coffee to show your appreciation.

7 thoughts on “How to Synchronize Time with Chrony NTP in Linux”

  1. On my system – Debian Bullseye with KDE desktop. Ntp does not work, Chrony does. I do not wreck my brain to figure it out. I will leave that to the code boys.

    Reply
  2. I have a dual boot W10/Ubuntu PC. When I boot to Ubuntu from W10, the displayed time is correct before the Ubuntu home page comes up, then decreases by 4 hours when the Ubuntu home page is displayed.

    When booting back to W10, the time stays in error by 4 hours.

    How do I get correct time without having to synchronize after every boot ?

    Reply
  3. Use ntpdate on machine where you don’t want to run a NTP server. A simple Cron task can automate time synchronization with a upstream NTP server.

    Reply

Leave a Reply to Ravi Saive Cancel reply

Thank you for taking the time to share your thoughts with us. We appreciate your decision to leave a comment and value your contribution to the discussion. It's important to note that we moderate all comments in accordance with our comment policy to ensure a respectful and constructive conversation.

Rest assured that your email address will remain private and will not be published or shared with anyone. We prioritize the privacy and security of our users.