13 Linux Network Configuration and Troubleshooting Commands

Computers are connected in a network to exchange information or resources each other. Two or more computer connected through network media called computer network. There are number of network devices or media are involved to form computer network. Computer loaded with Linux Operating System can also be a part of network whether it is small or large network by its multitasking and multiuser natures. Maintaining of system and network up and running is a task of System / Network Administrator’s job. In this article we are going to review frequently used network configuration and troubleshoot commands in Linux.

Linux Network Configuration Commands

Linux Network Configuration and Troubleshooting Commands

1. ifconfig

ifconfig (interface configurator) command is use to initialize an interface, assign IP Address to interface and enable or disable interface on demand. With this command you can view IP Address and Hardware / MAC address assign to interface and also MTU (Maximum transmission unit) size.

# ifconfig

eth0      Link encap:Ethernet  HWaddr 00:0C:29:28:FD:4C
          inet addr:  Bcast:  Mask:
          inet6 addr: fe80::20c:29ff:fe28:fd4c/64 Scope:Link
          RX packets:6093 errors:0 dropped:0 overruns:0 frame:0
          TX packets:4824 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:6125302 (5.8 MiB)  TX bytes:536966 (524.3 KiB)
          Interrupt:18 Base address:0x2000

lo        Link encap:Local Loopback
          inet addr:  Mask:
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:480 (480.0 b)  TX bytes:480 (480.0 b)

ifconfig with interface (eth0) command only shows specific interface details like IP Address, MAC Address etc. with -a options will display all available interface details if it is disable also.

# ifconfig eth0

eth0      Link encap:Ethernet  HWaddr 00:0C:29:28:FD:4C
          inet addr:  Bcast:  Mask:
          inet6 addr: fe80::20c:29ff:fe28:fd4c/64 Scope:Link
          RX packets:6119 errors:0 dropped:0 overruns:0 frame:0
          TX packets:4841 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:6127464 (5.8 MiB)  TX bytes:539648 (527.0 KiB)
          Interrupt:18 Base address:0x2000

Assigning IP Address and Gateway

Assigning an IP Address and Gateway to interface on the fly. The setting will be removed in case of system reboot.

# ifconfig eth0 netmask

Enable or Disable Specific Interface

To enable or disable specific Interface, we use example command as follows.

Enable eth0
# ifup eth0
Disable eth0
# ifdown eth0

Setting MTU Size

By default MTU size is 1500. We can set required MTU size with below command. Replace XXXX with size.

# ifconfig eth0 mtu XXXX

Set Interface in Promiscuous mode

Network interface only received packets belongs to that particular NIC. If you put interface in promiscuous mode it will received all the packets. This is very useful to capture packets and analyze later. For this you may require superuser access.

# ifconfig eth0 - promisc

2. PING Command

PING (Packet INternet Groper) command is the best way to test connectivity between two nodes. Whether it is Local Area Network (LAN) or Wide Area Network (WAN). Ping use ICMP (Internet Control Message Protocol) to communicate to other devices. You can ping host name of ip address using below command.

# ping

PING ( 56(84) bytes of data.
64 bytes from icmp_seq=1 ttl=44 time=203 ms
64 bytes from icmp_seq=2 ttl=44 time=201 ms
64 bytes from icmp_seq=3 ttl=44 time=201 ms


# ping www.tecmint.com

PING tecmint.com ( 56(84) bytes of data.
64 bytes from icmp_seq=1 ttl=47 time=284 ms
64 bytes from icmp_seq=2 ttl=47 time=287 ms
64 bytes from icmp_seq=3 ttl=47 time=285 ms

In Linux ping command keep executing until you interrupt. Ping with -c option exit after N number of request (success or error respond).

# ping -c 5 www.tecmint.com

PING tecmint.com ( 56(84) bytes of data.
64 bytes from icmp_seq=1 ttl=47 time=285 ms
64 bytes from icmp_seq=2 ttl=47 time=285 ms
64 bytes from icmp_seq=3 ttl=47 time=285 ms
64 bytes from icmp_seq=4 ttl=47 time=285 ms
64 bytes from icmp_seq=5 ttl=47 time=285 ms

--- tecmint.com ping statistics ---
5 packets transmitted, 5 received, 0% packet loss, time 4295ms
rtt min/avg/max/mdev = 285.062/285.324/285.406/0.599 ms


traceroute is a network troubleshooting utility which shows number of hops taken to reach destination also determine packets traveling path. Below we are tracing route to global DNS server IP Address and able to reach destination also shows path of that packet is traveling.

# traceroute

traceroute to (, 30 hops max, 60 byte packets
 1 (  0.217 ms  0.624 ms  0.133 ms
 2 (  2.343 ms  1.910 ms  1.799 ms
 3  221-231-119-111.mysipl.com (  4.334 ms  4.001 ms  5.619 ms
 4 (  5.386 ms  6.490 ms  6.224 ms
 5  gi0-0-0.dgw1.bom2.pacific.net.in (  7.798 ms  7.614 ms  7.378 ms
 6 (  10.852 ms  5.389 ms  4.322 ms
 7  ix-0-100.tcore1.MLV-Mumbai.as6453.net (  5.836 ms  5.590 ms  5.503 ms
 8  if-9-5.tcore1.WYN-Marseille.as6453.net (  216.909 ms  198.864 ms  201.737 ms
 9  if-2-2.tcore2.WYN-Marseille.as6453.net (  203.305 ms  203.141 ms  202.888 ms
10  if-5-2.tcore1.WV6-Madrid.as6453.net (  200.552 ms  202.463 ms  202.222 ms
11  if-8-2.tcore2.SV8-Highbridge.as6453.net (  205.446 ms  215.885 ms  202.867 ms
12  if-2-2.tcore1.SV8-Highbridge.as6453.net (  202.675 ms  201.540 ms  203.972 ms
13  if-6-2.tcore1.NJY-Newark.as6453.net (  203.732 ms  203.496 ms  202.951 ms
14  if-2-2.tcore2.NJY-Newark.as6453.net (  203.858 ms  203.373 ms  203.208 ms
15 (  201.093 ms (  206.597 ms (  204.178 ms
16  ae9.edge1.NewYork.Level3.net (  205.960 ms  205.740 ms  205.487 ms
17  vlan51.ebr1.NewYork2.Level3.net (  203.867 ms vlan52.ebr2.NewYork2.Level3.net (  202.850 ms vlan51.ebr1.NewYork2.Level3.net (  202.351 ms
18  ae-6-6.ebr2.NewYork1.Level3.net (  201.771 ms  201.185 ms  201.120 ms
19  ae-81-81.csw3.NewYork1.Level3.net (  202.407 ms  201.479 ms ae-92-92.csw4.NewYork1.Level3.net (  208.145 ms
20  ae-2-70.edge2.NewYork1.Level3.net (  200.572 ms ae-4-90.edge2.NewYork1.Level3.net (  200.402 ms ae-1-60.edge2.NewYork1.Level3.net (  203.573 ms
21  b.resolvers.Level3.net (  199.725 ms  199.190 ms  202.488 ms

4. NETSTAT Command

Netstat (Network Statistic) command display connection info, routing table information etc. To displays routing table information use option as -r.

# netstat -r

Kernel IP routing table
Destination     Gateway         Genmask         Flags   MSS Window  irtt Iface    *        U         0 0          0 eth0
link-local      *          U         0 0          0 eth0
default         UG        0 0          0 eth0

For more examples of Netstat Command, please read our earlier article on 20 Netstat Command Examples in Linux.

5. DIG Command

Dig (domain information groper) query DNS related information like A Record, CNAME, MX Record etc. This command mainly use to troubleshoot DNS related query.

# dig www.tecmint.com; <<>> DiG 9.8.2rc1-RedHat-9.8.2-0.10.rc1.el6 <<>> www.tecmint.com
;; global options: +cmd
;; Got answer:
;; ->>HEADER<

For more examples of Dig Command, please read the article on 10 Linux Dig Commands to Query DNS.

6. NSLOOKUP Command

nslookup command also use to find out DNS related query. The following examples shows A Record (IP Address) of tecmint.com.

# nslookup www.tecmint.com

Non-authoritative answer:
www.tecmint.com canonical name = tecmint.com.
Name:   tecmint.com

For more NSLOOKUP Command, read the article on 8 Linux Nslookup Command Examples.

7. ROUTE Command

route command also shows and manipulate ip routing table. To see default routing table in Linux, type the following command.

# route

Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface    *        U     0      0        0 eth0
link-local      *          U     1002   0        0 eth0
default         UG    0      0        0 eth0

Adding, deleting routes and default Gateway with following commands.

Route Adding
# route add -net gw
Route Deleting
# route del -net gw
Adding default Gateway
# route add default gw

8. HOST Command

host command to find name to IP or IP to name in IPv4 or IPv6 and also query DNS records.

# host www.google.com

www.google.com has address
www.google.com has address
www.google.com has address
www.google.com has address
www.google.com has address
www.google.com has IPv6 address 2404:6800:4003:802::1014

Using -t option we can find out DNS Resource Records like CNAME, NS, MX, SOA etc.

# host -t CNAME www.redhat.com

www.redhat.com is an alias for wildcard.redhat.com.edgekey.net.

9. ARP Command

ARP (Address Resolution Protocol) is useful to view / add the contents of the kernel’s ARP tables. To see default table use the command as.

# arp -e

Address                  HWtype  HWaddress           Flags Mask            Iface             ether   00:50:56:c0:00:08   C                     eth0

10. ETHTOOL Command

ethtool is a replacement of mii-tool. It is to view, setting speed and duplex of your Network Interface Card (NIC). You can set duplex permanently in /etc/sysconfig/network-scripts/ifcfg-eth0 with ETHTOOL_OPTS variable.

# ethtool eth0

Settings for eth0:
        Current message level: 0x00000007 (7)
        Link detected: yes

11. IWCONFIG Command

iwconfig command in Linux is use to configure a wireless network interface. You can see and set the basic Wi-Fi details like SSID channel and encryption. You can refer man page of iwconfig to know more.

# iwconfig [interface]

12. HOSTNAME Command

hostname is to identify in a network. Execute hostname command to see the hostname of your box. You can set hostname permanently in /etc/sysconfig/network. Need to reboot box once set a proper hostname.

# hostname 


13. GUI tool system-config-network

Type system-config-network in command prompt to configure network setting and you will get nice Graphical User Interface (GUI) which may also use to configure IP Address, Gateway, DNS etc. as shown below image.

# system-config-network
Linux GUI Network Configuration

Linux GUI Network Configuration Tool

This article can be useful for day to day use of Linux Network administrator in Linux / Unix-like operating system. Kindly share through our comment box if we missed out.

If You Appreciate What We Do Here On TecMint, You Should Consider:

TecMint is the fastest growing and most trusted community site for any kind of Linux Articles, Guides and Books on the web. Millions of people visit TecMint! to search or browse the thousands of published articles available FREELY to all.

If you like what you are reading, please consider buying us a coffee ( or 2 ) as a token of appreciation.

Support Us

We are thankful for your never ending support.

Ravi Saive

I am Ravi Saive, creator of TecMint. A Computer Geek and Linux Guru who loves to share tricks and tips on Internet. Most Of My Servers runs on Open Source Platform called Linux. Follow Me: Twitter, Facebook and Google+

Your name can also be listed here. Got a tip? Submit it here to become an TecMint author.

RedHat RHCE and RHCSA Certification Book
Linux Foundation LFCS and LFCE Certification Preparation Guide
The Complete Linux System Administrator Bundle
Become an Ethical Hacker Bonus Bundle

You may also like...

51 Responses

  1. Pawan kumar says:

    dns is replying fine but internet is not working in Ubuntu.

    • Ethan Olmstead says:

      Easy fix, is your ping responding? if not check with the command “route -n” and make sure your gateways are lining up. If not type the command (With your IP address of your router, my example is the basic… “route add default gw” Then check the internet once again.

  2. ZapusT says:

    system-config-network doesn’t work on my KDE Neon

  3. Jeff Silverman says:

    This article is so out of date that it should be removed. In particular, use the ip command and use tracepath, not traceroute.

  4. Fábio says:

    Excellent list, all commands are very useful.

  5. Mir Shakil says:

    some command not working on kali

Leave a Reply to Ethan Olmstead Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.