How to Setup a DNS/DHCP Server Using dnsmasq on CentOS/RHEL 8/7
A Dynamic Host Configuration Protocol (DHCP) server dynamically assigns IP addresses and other network configuration parameters to each device on a network. A DNS forwarder on a LAN forwards DNS queries for non-local domain names to upstream DNS servers (outside that network). A DNS caching server answers recursive requests from clients so that the DNS query can be resolved faster, thus improving DNS lookup speeds to previously visited sites.
dnsmasq is a lightweight, easy to configure DNS forwarder, DHCP server software and router advertisement subsystem for small networks. Dnsmasq supports Linux, *BSD, Mac OS X as well as Android.
It features a DNS subsystem that provides a local DNS server for the network, with forwarding of all query types to upstream recursive DNS servers and caching of common record types. The DHCP subsystem supports DHCPv4, DHCPv6, BOOTP, PXE, and a TFTP server. And the router advertisement subsystem supports basic autoconfiguration for IPv6 hosts.
In this article, we will walk you through the instructions on how to install and setup DNS/DHCP Server Using dnsmasq on CentOS/RHEL 8/7 distributions.
Installing dnsmasq in CentOS and RHEL Linux
1. The dnsmasq package is available in the default repositories and can be easily installed using the YUM package manager as shown.
# yum install dnsmasq
2. Once the dnsmasq package installation is complete, you need to start the dnsmasq service for now and enable it to automatically start at system boot. Besides, check its status to ensure that it is up and running using the following systemctl commands.
# systemctl start dnsmasq # systemctl enable dnsmasq # systemctl status dnsmasq
Configuring dnsmasq Server in CentOS and RHEL Linux
3. The dnsmasq server can be configured via the /etc/dnsmasq.conf file (which contains well commented and explained options), and user-defined configuration files can also be added in the /etc/dnsmasq.d directory.
DNS is enabled by default, so before making any changes, make sure to create a backup of /etc/dnsmasq.conf file.
# cp /etc/dnsmasq.conf /etc/dnsmasq.conf.orig
4. Now open the /etc/dnsmasq.conf file using your favorite text-based editor and make the following suggested configuration settings.
# vi /etc/dnsmasq.conf
listen-address the option is used to set the IP address, where dnsmasq will listen on. To use your CentOS/RHEL server to listen for DHCP and DNS requests on the LAN, set the
listen-address option to its LAN IP addresses (remember to include 127.0.0.1) as shown. Note that the server IP must be static.
Related to the above, you can restrict the interface dnsmasq listens on using the interface option (add more lines for more than one interface).
5. If you want to have a domain (which you can set as shown next) automatically added to simple names in a hosts-file, uncomment the
6. To set the domain for dnsmasq, which means DHCP clients will have fully qualified domain names as long as the set domain is matched, and sets the “domain” DHCP option for all clients.
7. Next, also define the upstream DNS server for non-local domains using the server option (in the form server=dns_server_ip) as shown.
# Google's nameservers server=188.8.131.52 server=184.108.40.206
8. Then you can force your local domain to an IP address(es) using the address option as shown.
9. Save the file and check the configuration file syntax for errors as shown.
# dnsmasq --test
Configuring dnsmasq with /etc/resolv.conf File
10. In this step, you need to make all queries to be sent to dnsmasq by adding the localhost addresses as the only nameservers in /etc/resolv.conf file.
# vi /etc/resolv.conf
11. The /etc/resolv.conf file is maintained by a local daemon especially the NetworkManager, therefore any user-made changes will be overwritten. To prevent this, write-protect it by setting the immutable file attribute (disabling write access to the file) using the chattr command as shown.
# chattr +i /etc/resolv.conf # lsattr /etc/resolv.conf
Defining DNS Hosts and Names
12. The Dnsmasq reads all the DNS hosts and names from the /etc/hosts file, so add your DNS hosts IP addresses and name pairs as shown.
127.0.0.1 dnsmasq 192.168.56.10 dnsmasq 192.168.56.1 gateway 192.168.56.100 maas-controller 192.168.56.20 nagios 192.168.56.25 webserver1
Important: Local DNS names can also be defined by importing names from the DHCP subsystem, or by the configuration of a wide range of useful record types.
13. To apply the above changes, restart the dnsmasq service as shown.
# systemctl restart dnsmasq
14. If you have the firewalld service running, you need to open DNS and DHCP services in the firewall configuration, to allow requests from hosts on your LAN to pass to the dnsmasq server.
# firewall-cmd --add-service=dns --permanent # firewall-cmd --add-service=dhcp --permanent # firewall-cmd --reload
Testing Local DNS
15. To test if the local DNS server or forwarding is working fine, you need to use tools such as dig or nslookup for performing DNS queries. These tools are provided by the bind-utils package which may not come pre-installed on CentOS/RHEL 8, but you can install it as shown.
# yum install bind-utils
16. Once you have installed, you can run a simple query on your local domain as shown.
# dig tecmint.lan OR # nslookup tecmint.lan
17. You can also try to query the FQDN of one of the servers.
# dig webserver1.tecmint.lan OR # nslookup webserver1.tecmint.lan
18. To test a reverse IP lookup, run a similar command.
# dig -x 192.168.56.25 OR # nslookup 192.168.56.25
Enable DHCP Server Using dnsmasq
19. You can enable the DHCP server by uncommenting the
dhcp-range option and supply the range of addresses available for lease and optionally a lease time e.g (repeat for more than one network).
20. The following option defines where the DHCP server will keep its lease database, this will helps you to easily check IP addresses it has assigned.
21. To make the DHCP server to authoritative mode, uncomment the option.
22. Save the file and restart the dnsmasq service to apply the recent changes.
# systemctl restart dnsmasq
That brings us to the end of this guide. To reach us for any questions or thoughts you want to share about this guide, use the feedback form below.